Skip to content
PT SCBI

Data sheet · Parameters

Ash Content of Shisha Charcoal: The Range of Each Grade, Our Measured Value and What Ash Color Shows

This page belongs to the quality parameters and covers the ash content of shisha charcoal, the hookah charcoal or hookah coals of US and Canadian buyers, as this factory measures and grades it. It is written for the buyer comparing a grade or a laboratory report. Ash content is the one parameter that sets this factory's grades.

Written by
Henry Sinaga
Reviewed by
Dimas Setyawan,
Updated
Reading time
4 min read

Quick answer

What ash content does this factory's shisha charcoal have, and what does ash color show?

Ash sets this factory's grade, from 1.6–1.9% for Platinum to 2.3–2.5% for Premium, measured as received on the laboratory report of each shipment. The newest report on file, issued November 4, 2026, measured 1.64% as received, inside the Platinum range. Ash color is not on the report and sets no grade of these coconut shell charcoal briquettes.

Ash content at a glance

As confirmed, November 2026

Platinum
1.6–1.9%
Super Premium
1.9–2.3%
Premium
2.3–2.5%
Basis
As received (wet basis)
Value on a line
Sold as the lower grade
Newest report
1.64% as received, November 4, 2026
Method
ASTM D1762-84 (2021), furnace at 750 °C

1. What ash content is

Ash content is the part of a sample that does not burn, weighed after a full burn in a furnace.

Definition

ash content

Ash content is the share of a charcoal sample's mass left as mineral residue after the sample is burned completely in a laboratory furnace, stated in percent on a named basis, as received or dry.

In ASTM D1762-84 (2021), the method named on this factory's laboratory report, the sample is burned in a muffle furnace at 750 °C for 6 hours and the residue is weighed. The result is a percentage of the sample's mass on a stated reporting basis: as received, with the sample's moisture included, or dry, which gives a higher figure for the same charcoal.

How facts on this page are confirmed is set out in the editorial and review policy.

2. The ash range of each grade

Each of this factory's three grades is an ash range, and ash is the only parameter that separates them.

Ash content range of each grade of coconut shell charcoal briquettes at this factory, read on the figure as received (wet basis); ranges confirmed by the owner in November 2026.
GradeAsh content
Platinum 1.6–1.9%
Super Premium 1.9–2.3%
Premium 2.3–2.5%

A value exactly on the line between two ranges is sold as the lower grade, the grade with the higher ash range. The grades page sets out the ash content limit of each grade beside what a shisha charcoal grade does not promise.

3. Our measured ash

The newest laboratory report on file measured 1.64% ash as received.

It was issued on November 4, 2026, by Carsurin Tbk, Semarang, for one export shipment, under the factory's practice of a COA from the laboratory for each order. The value sits inside the Platinum range of 1.6–1.9%. One report covers one shipment, so it does not describe the next one.

Ash content of each laboratory report on file for this factory's coconut shell charcoal briquettes, as received, by issue date; each report covers one export shipment.
Report issuedAsh (as received)Laboratory
November 4, 2026 1.64%Carsurin Tbk, Semarang

Results from further shipments are added to the measured ash content of our last batches as they are tested.

4. What raises ash, and how the factory holds it

Ash is the mineral part of what goes into the mix, so the factory holds it at intake, at the sieve and at the batch check.

FAO's handbook on charcoal making names earth and sand contamination among the causes of high ash in charcoal. This factory's raw material is bought as carbonized shell charcoal from carbonizers, and each delivery is checked; see how incoming shell charcoal is checked.

Note

Where ash is held

  • At intake. Ash content and ash color are among the checks on each delivery of shell charcoal.
  • After milling. 4 hammer mills, then a 10 m rotary sieve in 5 cleaning passes.
  • At the batch check. High ash is one of four reasons a batch fails: smell or smoke on warming up, high ash, cracks or breakage and inconsistent size or density.

5. What ash color does and does not show

Ash color is seen, not measured, and no grade or laboratory report at this factory states it.

The laboratory weighs the residue and does not record its color. At this factory ash color is one of the intake checks on shell charcoal, and in use it is judged by eye after a burn, as in a sample test. Color and amount are different observations: a light color does not show a low ash figure, and a low figure does not promise a color.

Caution

What ash color can and cannot tell you

  • It can show whether the ash of a delivery looks like the ash of the approved sample burned the same way.
  • It cannot show the ash content, the grade or the laboratory result of the shipment.

To compare ash fairly, burn the sample and your current charcoal on one device in one session, as in the sample test protocol.

Questions buyers ask

Why does my laboratory's ash figure differ from yours?
Check three things: the basis, since a dry-basis figure is higher than the as-received one; the method, since furnace temperature and time are set by it; and the shipment, since each report covers one sample of one shipment. Compare figures only when all three match.
Is white ash a sign of low ash content?
Not on its own. The laboratory weighs the residue, and color is judged by eye. At this factory ash color is one of the intake checks on shell charcoal, but no grade and no laboratory report states it.

Sources

  1. ASTM D1762-84(2021), Standard Test Method for Chemical Analysis of Wood Charcoal (the edition named on the laboratory report) (opens in new tab), ASTM International — accessed
  2. Simple technologies for charcoal making (FAO Forestry Paper 41), chapter 10: Using charcoal efficiently (opens in new tab), Food and Agriculture Organization of the United Nations — accessed

Test before you commit a container

Samples ship with the batch COA; third-party inspection on request.