Skip to content
PT SCBI

Data sheet · Parameters

Moisture Content of Shisha Charcoal: At the Oven, on the Laboratory Report and on Arrival

This page belongs to the quality parameters and follows the moisture of shisha charcoal, the hookah charcoal or hookah coals of US and Canadian buyers, from the factory's ovens to the buyer's warehouse. It is written for the buyer who reads a laboratory report or measures a delivery. Moisture is held at the oven and stated on the report as received.

Written by
Henry Sinaga
Reviewed by
Dimas Setyawan,
Updated
Reading time
5 min read

Quick answer

How much moisture is in this factory's shisha charcoal, from the oven to arrival?

Briquettes leave the ovens at 2% moisture at most, checked with a meter on every oven load; the laboratory report states moisture as received. The newest report on file, issued November 4, 2026, states 3.21% as received, measured on a shipment sample after weathering and packing. No grade of these coconut shell charcoal briquettes sets a moisture limit.

Moisture at a glance

As confirmed, November 2026

Leaving the oven
2% at most
Oven check
Measured with a moisture meter on every oven load
Drying
Electric ovens, a slow cycle of 48 hours or more
Weathering
14 days
Shell charcoal at intake
Below 12%
Newest report
3.21% as received, November 4, 2026
Grade limit
None; ash alone sets the grade
Method
ASTM D1762-84 (2021), oven at 105 °C

1. What moisture content is

Moisture content is the water in a sample, found by drying the sample and weighing what it lost.

Definition

moisture content

Moisture content is the share of a charcoal sample's mass that is water, measured as the mass lost when the sample is dried at a set temperature, and stated in percent of the sample as received.

In ASTM D1762-84 (2021), the method named on this factory's laboratory report, the sample is dried in an oven at 105 °C for 2 hours. The result is a percentage of the sample as received, and the batch COA register copies it from the report.

How facts on this page are confirmed is set out in the editorial and review policy.

2. Moisture at the oven

A batch leaves the ovens at moisture of 2% at most, and every load is checked.

Drying runs in electric ovens, a slow cycle of 48 hours or more, and moisture is measured with a moisture meter on every oven load. The step is set out on the drying page, and the rest after it on the page about the weathering yard.

Moisture of this factory's coconut shell charcoal briquettes at each point on file, from intake to arrival; the laboratory value is as received, from the report issued November 4, 2026.
PointLimit, check or valueWhere the figure comes from
Shell charcoal at intake Below 12%The factory's intake check
Briquettes leaving the oven 2% at most, measured with a moisture meter on every oven loadThe factory's oven check
Before packing 14 days of weathering, under cover in the open airThe weathering record
Sample of an export shipment 3.21% as receivedThe laboratory report issued November 4, 2026
On arrival Not measured by the factoryYour own measurement

3. Moisture on the laboratory report

The newest laboratory report on file states moisture of 3.21% as received.

The sample was drawn from an export shipment, after weathering and packing, so it is not the oven reading. FAO's handbook on charcoal making notes that charcoal takes up moisture from humid air quickly, enough to reach about 5 to 10% even in well-burned charcoal, so a report can sit above the oven limit. Results from further shipments are added to the measured moisture content of our last batches as they are tested.

No grade carries a moisture limit at this factory: the grades page sets each grade by ash alone.

4. Moisture on arrival

Moisture on arrival is the buyer's own measurement, and it can differ from the report.

Between packing and your warehouse the cartons travel in a closed container, and charcoal keeps exchanging moisture with the air around it; FAO notes that the natural or equilibrium moisture of charcoal can rise to 15% or more. To compare like with like, check moisture on arrival in four steps.

  1. Step 1

    Sample across the load

    Not one carton. Take pieces from cartons at several points in the load rather than from the carton nearest the door.

  2. Step 2

    Use the report's method and basis

    Like with like. Ask your laboratory for moisture by ASTM D1762-84, as received, so the figure compares with the report.

  3. Step 3

    Write down the dates

    Arrival and test. Record the date the container arrived and the date the pieces were tested beside each result.

  4. Step 4

    Report a difference in time

    Inside the window. A quality problem is reported within 14 days of the arrival of the container at the buyer's warehouse.

Moisture after shipping is covered on the moisture-on-arrival page, and the claim route on the claims and remedies page.

5. Why moisture matters

Water in a briquette has to be driven off before the charcoal gives its heat.

FAO's handbook calls moisture an adulterant that lowers the calorific or heating value of charcoal: the water must be evaporated on burning, a direct loss of heating power. How heat is measured is on the calorific value page.

Moisture also enters the arithmetic of the report. Fixed carbon is what remains once moisture, ash and volatile matter are taken out, so the same charcoal shows less fixed carbon as received than dry; see how fixed carbon is calculated.

Questions buyers ask

Why is the moisture on your COA higher than the oven limit?
The laboratory sample is drawn from an export shipment, after weathering and packing, and charcoal takes up moisture from the air. FAO's charcoal handbook notes that this absorption is rapid. The oven limit applies when a batch leaves the oven.
Will the moisture be the same when my container arrives?
Not necessarily. Measure it on arrival by the same method and on the same basis as the report, and compare like with like. A quality problem is reported within 14 days of the arrival of the container at the buyer's warehouse.
Can a moisture limit be written into my order?
No grade carries a moisture limit; the factory's own limit is 2% at most at the oven. A limit you need is raised before the order, and the proforma invoice is the specification.

Sources

  1. ASTM D1762-84(2021), Standard Test Method for Chemical Analysis of Wood Charcoal (the edition named on the laboratory report) (opens in new tab), ASTM International — accessed
  2. Simple technologies for charcoal making (FAO Forestry Paper 41), chapter 10: Using charcoal efficiently (opens in new tab), Food and Agriculture Organization of the United Nations — accessed

Test before you commit a container

Samples ship with the batch COA; third-party inspection on request.