Skip to content
PT SCBI

Guide · Parameters

Burn Time and Heat of Shisha Charcoal: What They Depend On, Our Bench Method and What We Do Not Guarantee

This page belongs to the quality parameters and covers the burn time and heat of shisha charcoal, the hookah charcoal or hookah coals of US and Canadian buyers. It is written for the buyer who is asked how long a piece lasts. It sets out what burn time depends on, what this factory measures and what it does not promise.

Written by
Henry Sinaga
Reviewed by
Dimas Setyawan,
Updated
Reading time
4 min read
A burn test records ignition time, heat stability and the ash left after a full burn under one fixed bowl-and-airflow setup.

Quick answer

How long does shisha charcoal burn, and how does this factory measure it?

Burn time depends on piece size, density and heating; this factory times 3 pieces on an electric coil, recording time to light and burn time. No minutes figure is published for these coconut shell charcoal briquettes, because the bowl, device and airflow are set by the user. Compare burn time on your own setup, beside the charcoal you use now.

1. What burn time depends on

Burn time is set as much by how a piece is heated and used as by the piece itself.

Definition

burn time

Burn time is the time a briquette stays lit and gives usable heat, from ignition until it is reduced to ash, measured under stated conditions of piece size, heat source, bowl and airflow.

What sets the burn time of coconut shell charcoal briquettes, and who controls each factor; the effect of volatile matter is cited to a 2025 peer-reviewed study of commercial charcoals.
FactorWhat it coversSet by
Piece size and mass The shape and size orderedThe factory, to the order
Density How tightly the mix is pressedThe factory: mixing and pressing
Volatile matter High volatiles speed up combustion (2025 study)The factory: the shell charcoal accepted
Heating How the piece is lit and how long it is heatedThe user
Bowl, device and airflow Heat-management device, foil, the draw on the pipeThe user
Piece size and shape are set by the order; the bowl, device and airflow are set by the user.

Of this factory's cube sizes, the owner names the 27 mm cube for longer sessions; see the 27 mm cube. No burn time is stated per size.

How facts on this page are confirmed is set out in the editorial and review policy.

2. Our bench method

The factory times 3 pieces lit on an electric coil and writes down time to light and burn time.

The burn bench method on file for this factory's coconut shell charcoal briquettes, as confirmed by the owner in November 2026; items not on file are marked.
ItemOn file
Heat source An electric coil
Pieces per test 3
Recorded Time to light and burn time
End point, bowl, airflow and frequency Not on file

Lighting every piece on the same kind of heater keeps one batch comparable with the next. The bench results are not published in a register yet.

3. Heat, and what the laboratory results say about it

Heat is not timed on the bench, and the laboratory results bear on it only indirectly.

The heat a piece can give is its calorific value, which is not on the laboratory report on file; see the calorific value page. FAO's handbook on charcoal making notes that moisture lowers the heating value of charcoal, so the moisture on the report bears on it (moisture content), and volatile matter shapes how a piece lights and how fast it burns (volatile matter).

The batch COA register holds laboratory results, not burn times.

4. What we do not guarantee

No burn time, heat output or number of sessions is guaranteed, because the user sets part of what decides them.

Caution

Not promised

  • A minutes figure for one piece or one session.
  • A heat output for a piece or a bowl.
  • A number of sessions per box or per kilogram.

No grade sets a burn time either: the grades page sets each grade by ash alone, and a higher grade is not a longer burn by itself.

5. Comparing burn time yourself

Burn time is compared on your own setup, side by side with the charcoal you use now.

Light the sample and your current charcoal the same way, burn them in the same bowl with the same device and airflow in one session, and write down the time to light and the burn time of each, as the sample test protocol sets out. A sample test on your device answers the question a spec sheet cannot.

Burn time compares fairly only between pieces burned on one setup in one session.

Questions buyers ask

How long does one piece of your shisha charcoal burn?
No minutes figure is published. The factory times 3 pieces lit on an electric coil, but a burn time measured that way does not carry over to your bowl, device and airflow. Time pieces on your own setup, next to the charcoal you use now.
Why do you not guarantee a burn time?
Burn time depends on the piece size, the density, the way the piece is heated and the bowl and airflow it burns in. The last three are set by the user, so a figure measured at the factory cannot be promised for every session.

Sources

  1. Mencarelli, Greco and Grigolato (2025), Grilling and air pollution: how charcoal quality affects emissions, Air Quality, Atmosphere & Health 18, 1757–1770 (opens in new tab), Springer Nature — accessed
  2. Simple technologies for charcoal making (FAO Forestry Paper 41), chapter 10: Using charcoal efficiently (opens in new tab), Food and Agriculture Organization of the United Nations — accessed

Test before you commit a container

Samples ship with the batch COA; third-party inspection on request.